Comments for Qnap Advanced Support

Comment on iSCSI Targets Get Lost Suddenly, How Can I Restore Them? by frank

frank — Sat, 11 May 2019 19:51:17 +0000

QNAP Garbage. This should not happen!
It happen to me once. No more QNAP for me. Horrible piece of SH#$

Comment on Error Page Not Found Or The Web Server Is Currently Unavabile. Please Contact The Website Admin For Help by Frank

Frank — Wed, 01 Aug 2018 17:28:47 +0000

That doesn’t change a thing. I have other QNAP that doesn’t have web server enable and it’s working. This isn’t related with Web Server.

Comment on Qnap Folder, User Rights & Folder Access Problems by cemal

cemal — Fri, 02 Jun 2017 13:13:33 +0000

Client üzerinden media klasörüne ulaşmaya çalışırken kullanıcı adı ve şifre istiyor ancak hiçbir kullanıcıyı kabul etmiyor

Comment on How to Start / Stop Services on Qnap by Christopher Edgar

Christopher Edgar — Wed, 24 May 2017 04:58:37 +0000

How do I selectively manage whether services start or stop? Currently you are referencing only one master script but when I fire it up, I run out of memory and my QTS 4.3.3 box crashes. I’d like to be able to selectively start services manually so I don’t crash my box when it tries to launch every application/service I have installed on the box. Specifically container station crashes my box as soon as it starts up. I’d like to set it to manual instead of automatic startup.

Comment on How to use virtual disk on your QNAP NAS by ike

ike — Thu, 06 Apr 2017 15:14:37 +0000

I have setup a VirtualDisk in my QNAP NAS and wish to use it to create versioning backup of local volumes/shares.
However, I tried Backup Station and Hybrid Backup Sync, both do not allow me to choose VirtualDisk as destination !!!

Comment on Pre-Sales Support by wilson

wilson — Thu, 06 Apr 2017 09:30:31 +0000

I have QNAP TS-259 ( not pro or pro+ ). I can’t see this model from QNAP support site. Instead, I only see TS-259pro / TS-259pro+.

I want to setup my TS-259 for TimeMachine, is there a way to do that? I don’t see the “TimeMachine” option listed when I logged into my NAS.

thanks
Wilson

Comment on Meaning of Led Lights and Alarm Buzzer by Rens51

Rens51 — Sun, 26 Mar 2017 14:01:44 +0000

I have the QNAP TS-410, RAID5 (4 Samsung discs 1 TB each), ±60% used.
It has the latest firmware, it worked ok via http:// and it was visible through Finder, under external devices until I had to reformat my MacBookPro (corrupt OSX).

I did re-install the MBPro OSX (latest Sierra) en recovered my hard-disk content from my external back-up disc (not my QNAP) with Time Machine. The MBPro works fine again.
However, since then I don’t see my QNAP anymore, not in Finder, not through http://, and not with QFinder Pro.

The QNAP is LAN connected, the same LAN as my MBPro.

QNAP LED’s status are: (as indicated above)
My Status LED flashes red-green every 0.5 seconds.
My LAN status indicates activity as it flashes intermittently.
USB and eSATA leds are off.
I see 4 green lights above my discs.

I’ve tried to reboot the QNAP through power-off, power-on, no result.
I’ve reset my QNAP with the little button on the back, no result.
The LED lights come back with the same status as indicated above.

What to try/do next?
I appreciate your advice!
Thanks, Rens
btw I’ve left the QNAP in this status for 5+ days, assuming rebuild of discs.

Comment on External Drive Backup by prifti

prifti — Fri, 24 Mar 2017 20:07:45 +0000

Hello qnap team!
I have a Seagate 3TB HDD formated as ext4 and connected via usb3. I became following errors when i execute my rsync commands via ssh. state of HDD is “GOOD”
“rsync: write failed on /…./ Read-only file system (30) rsync error: error in file IO (code 11) at receiver.c(302) [receiver=3.0.7] rsync: connection unexpectedly closed (17455 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [sender=3.0.7].
what can i do to resolve it?
thanks in advance

Comment on Qnap Web Server: Host Your Own Websites in A Place by David Gall

David Gall — Sat, 11 Feb 2017 00:13:45 +0000

Sounds simple, but it didn’t work. Do you have any details on dealing with Port Forwarding? I suspect there are details regarding Ports, Router Port Settings and DNS that everyone is glossing over. I believe this is my problem.

thanks,

Comment on Qnap Netork / IP Settings by murdock

murdock — Thu, 09 Feb 2017 13:55:38 +0000

Can insert the static arp into my qnap ts-439 pro 2? Thanks a lot

Carlo