Qnap’ı Sıfırlamak / Yeniden Kurmak İstiyorum

1. Yöntem :

Qnap’ı kapatın ve HDD’leri çıkartın. Cihazı HDD’ler olmadan tekrar açın. Cihazı Qnapfinder ile network üzerinden bulunur hale geldiğinde kurulum adımlarını başlatın. Sizden disk istendiğinde diskleri 15 ‘e saniye aralıklarla olmak üzere yerleştirin ve kuruluma başlayın. Bu Qnap’ı tamamen sıfırdan yeniden kurmanızı sağlayacaktır.

2. Yöntem :

Administration page ->Reset to Factory Defaults kısmına girererekte Qnap’ı tamamen sıfılayabilirsiniz, ama ben herzaman ilk yöntemin daha sağlıklı olduğnu düşünüyorum.


Qnap’ı Resmi Dökümanı;

Complete Reinitialization

The following information is two methods for performing a complete re-installation of a QNap NAS. The first involves hot swapping the hard disks at a particular point in the process. The second involves installing the hard disks in another computer and using an application to remove the partitions from the drives.


Method 1 (Hot swapping)

  1. Remove your HDD(s) from the tray (if for TS-109, the same).
  2. Boot up the NAS without HDD(s) installed. You will hear a short beep,  and after about 1~2 minutes, a long beep.
  3. The system will use the embedded image to boot up.
  4. Then run the Finder on your PC, it will help you to find the NAS on the network.
  5. Use the default ID (admin) and password (admin) to login if it asks.
  6. Hot-plug the HDD(s) into the NAS.
  7. Go through the installation process including formating hard disk and installing the firmware.

Method 2 (Manually removing partitions using a Windows PC)

  1. Shut down the NAS and remove the HDD(s) from the tray.
  2. Install the HDD(s) in a Microsoft Windows client machine.
  3. Boot the client computer and open the Computer Management application. (Right click My Computer –> Manage)
  4. Locate the HDD(s) from the NAS in the Disk Management section and delete all the partitions.
  5. Shut down the client computer and remove the HDD(s).
  6. Install the HDD(s) in the NAS.
  7. Boot the NAS. As there is no OS installed the NAS uses its embedded image to boot.
  8. Run the QNAP Finder application on the client machine to locate and connect to the NAS.
  9. Use the default username (admin) and password (admin) to login if it ask.
  10. Go through the installation process including formatting the HDD(s) and installing the firmware.

Method 3 (Manually removing partitions using QNAP)

  1. On TS110, TS210 there is fdisk available. So login to your QNAP with ssh and type in mount on the list find the device binded with /share/HDA_DATA (for single disk configuration) or /share/MD0_DATA (for raid configurations). Launch fdisk with the disk as a parameter and remove all partitions.
  1. There is also another more brutal way to destroy the partition table on the disk: dd if=/dev/urandom of=<name of your HDD device> bs=1024k count=1.
VN:F [1.9.22_1171]
Rating: 7.7/10 (22 votes cast)
VN:F [1.9.22_1171]
Rating: +6 (from 10 votes)
Qnap'ı Sıfırlamak / Yeniden Kurmak İstiyorumI Want To Complete Reset / Re-Install Qnap, 7.7 out of 10 based on 22 ratings

2 Responses to Qnap’ı Sıfırlamak / Yeniden Kurmak İstiyorum

  1. Claus says:

    What if I have a Qnap with 2 bays, and they are running with no raid, two drives.
    My HDD in bay1 dead, and I changed it.

    Can I reset and still keep the data on hdd2 (Bay2)???

  2. burado51 says:

    This kind of configration files stored in HDD’s, so if you start device with any HDD from part of your RAID, Qnap try to get back configration on this HDD,

    If your start Qnap with new HDD in first bay, Qnap may try to format whole system, so you can try this to use device without loosing data or configration;

    1 – Power off the NAS,
    2 – Plug out first HDD (broken HDD)
    3 – Start device back again withput this HDD,

    After device start, you should able to enter interface back again. Now you can plug in new HDD in first HDD slot. Format first drive in Volume configration to use it.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>