Qnap’ın Arkasındaki Reset Tuşu Ne İşe Yarar?

I – Reset Tuşu Ne İşe Yarar;

II – Reset Tuşu Nerede?

III – Reset Sonrasında Tüm Klasörlerim Kayboldu!

 

I – Reset Tuşu Ne İşe Yarar;

Qnap’ın arkasındaki reset tuşune ne işe yarar? Basarsam verilerimi kaybedermiyim?

 

System

Basic system reset

(1 beep)

Advanced system reset

(2 beeps)

All NAS models

Press the reset button for 3 sec

Press the reset button for 10 sec

Basit Reset (3 saniye / Tek Bip Sesi Duyana Kadar)

After pressing the reset button for 3 seconds, a beep sound will be heard. The following settings will be reset to default:

System administration password: admin.
TCP/IP configuration: Obtain IP address settings automatically via DHCP.
TCP/IP configuration: Disable Jumbo Frame.
TCP/IP configuration: If port trunking is enabled (dual LAN models only), the port trunking mode will be reset to “Active Backup (Failover)”.
System port: 8080 (system service port).
Security level: Low (Allow all connections).
LCD panel password: (blank)*.
VLAN will be disabled.
Service binding: All NAS services run on all available network interfaces.

*This feature is only provided by the NAS models with LCD panels. Please visit http://www.qnap.com for details.

Gelişmiş Sistem Reseti (10+ saniyeden fazla / 2 bip sesi duyana kadar)

After pressing the reset button for 10 seconds, you will hear two beeps at the third and the tenth seconds. The NAS will reset all the system settings to default as it does by the web-based system reset in “Administration” > “Restore to Factory Default” except all the data are reserved. The settings such as the users, user groups, and the network shares previously created will be cleared. To retrieve the old data after advanced system reset, create the same network shares on the NAS and the data will be accessible again.

 

II – Reset Tuşu Nerede?

Qnao Reset Button

 

III – Reset Sonrasında Tüm Klasörlerim Kayboldu!

Qnap Üzerindeki Tüm Klasörlerim Kayboldu

Eğer Qnap’ın arkasındaki Reset tuşuna 10 saniyeden fazla basarsanız Qnap kalsör yollarını kaybedecektir. Ayrıca Qnap’ın çok eski firmware’lerinde çok ender de olsa bazı kullancılarımız bu hata ile karşılaşabiliyorlardı. Qnap’taki Klasör yollarını tekrar göstermek için lütfen aşağıdaki adımları uygulayın.

Qnapte Access Right Managment -> Share Folders -> New Share Folder’a girin.

Çıkan ekranda next dedikten sonra “Folder Name” kısmına dilediğiniz bir isim (eski klasörünüzün ismi olabilir) girdikten sonra Path altında bulunan “Enter path manually” segmesine bastığınızda burada Qnap üzerindeki klasörlerinizi görebiliyor olmanız gerekiyor.

İstediğiniz klasörü seçip yetkilendirmeyi tamamlarsanız artık klasörünüze ulaşabiliyor olmanız gerekiyor.

VN:F [1.9.22_1171]
Rating: 10.0/10 (6 votes cast)
VN:F [1.9.22_1171]
Rating: +1 (from 1 vote)
Qnap'ın Arkasındaki Reset Tuşu Ne İşe Yarar?What is Reset Button Function?, 10.0 out of 10 based on 6 ratings

One Response to Qnap’ın Arkasındaki Reset Tuşu Ne İşe Yarar?

  1. Stefan Carlstedt says:

    I have a old TS-251+ and i can´t log in to it anymore. Have tried reset it but it doesen´t respond to 3sek or 10sek (tried much longer) What to do?

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>